Highline Bobby L
The Highline Bobby L
The combination of the High Line “Bobby” S with two High Line “Bobby” Bass Extensions creates the High Line “Bobby” L, an absolutely performance oriented High End Set, with up to 400 watt power handling and incredible dynamic reserves.
In this particularly slim and full-size, full-passive bass reflex combination, 4 specifically interconnected 8 inch woofers provide a particularly clearly structured bass foundation with clear high-end ambitions, while the proven High Line “Bobby” S configuration in the center enchants the listener with its combination of midrange tweeter and horn tweeter.
SPL: 88 dB
Impedanz: 8 Ohm
Frequency Range: 45 Hz – 24800 Hz
Crossover Frequency: 2400 Hz, 6/12 dB
Colors: The colors of the housing and horn can be chosen individually
Weight: 47 kg (per piece)
Height: 1635mm Width Front: 230mm Width Rear: 280mm Depth: 290mm
The Bobby Bass Extension is a passive speaker with an integrated crossover, which is designed as a perfect match to the Bobby S hornspeakers.
It has exactly the correct height to serve as a stand for the Bobby S.
There are two options to use the Bobby Bass Extensions:
Add one Bobby Bass Extension under the Bobby S, and you will get a Bobby M.
Add another Bobby Bass Extension on top of the Bobby S, and you will get a Bobby L.
— FINELY SELECTED AND MODIFIED
As bass speakers we use 2 pieces of the same 6” speaker with a carbon coated natural fiber cone, and extremely little mechanical losses as in the Bobby S.
By this we ensure to get a sonic characteristics which perfectly fits to the Bobby S.
The diaphragms of the bass is also treated with SteinMusic Maestro lacquer. This treatment gives a very natural sonic signature, which is equal all over the entire frequency range that the Bobby M or L is able to reproduce. We source those drivers from one of the best manufacturers, and besides the cone treatments we further modify and optimize them in many aspects to reduce mechanical losses and get an open sound with lots of detail and no colorations.
The bass speakers in detail
– Vented cast aluminum chassis for optimum strength and low compression
– Proprietary cone material with natural fibers
– Soft low damping rubber surround for transient response
– Non-conducting fiber glass voice coil former for minimum damping
– Extended copper sleeve on pole piece for low inductance and low distortion
– CCAW voice coil for reduced moving mass
– Long life silver lead wires
– Vented pole piece for reduced compression
The tweeter in detail
– Copper cap for reduced voice coil inductance and minimum phase shift
– Non-reflective rear chamber with optimized damping for improved dynamics
– Flow optimized vented pole piece for optimum coupling to rear chamber
– Fine weave soft fabric dome for smooth frequency response
– Saturation controlled motor system for low distortion
– CCAW voice coil for low moving mass
– Long life silver lead wires
– Low resonance frequency
The internal wiring is made of the finest solid core copper conductors. The diameter for the bass is 1mm, for the tweeter we use exactly the same style of conductors but decreased the diameter to 0,5mm. The result is a better resolution of the higher frequencies, maintaining a coherent overall reproduction.
— HANDMADE AND DEVELOPED INHOUSE
Before designing a crossover, we carefully tuned and adjusted the drivers so that we can achieve the best results with a simple configuration that ensures that no details of the music in this area of the speaker are lost.
— MANUFACTURED IN OUR WORKSHOP
Cabinet Bobby S
The cabinet is a ventilated cabinet with short tubes in the front behind the high frequency horn. It is wider at the back than at the front in a precisely defined ratio, which we have empirically found to be the best solution. An important aspect of this construction is that there are no standing waves between the side walls. Secondly, in combination with the 40mm thick rear panel, it gives the cabinets enormous stability against unwanted resonances. This allows us to work without any internal damping material, which not only absorbs unwanted resonances, but also takes energy out of the
music. The Bobby S are equipped with solid walnut feet for a transparent but organic sound.
Cabinet Bobby Bass Extension
The housing is a vented box. The bass reflex tunnels are located close to the bottom, and we have chosen a contour that changes its diameter slowly over the length. Be this we get a much better contour of the bass. The housing is wider in the back than in the front in an exactly defined ratio that we empirically found out to be the best solution here. One important aspect of this construction is that we will not have standing waves between the sidewalls, which in addition are stiffened with a bar. This gives the housings an enormous stability against unwanted housing resonances. This allows us to work completely without any internal dampening material, which does not only absorb unwanted resonances but also always sucks out energy from the music.
Also the Bobby Bass Extension are equipped with solid walnut feet for a transparent but organic sound.
One pairs of speaker terminals at the Bobby S speakers allow the use in bi-wiring or bi-amping. The choice of speaker terminals was a result of long listening tests of different models.
We finally decided for a sturdy version that allows the use of banana plugs or spades.
There are no further switches necessary, but depending on the positioning and characteristics of the listening room and personal preferences, you may use some of the acoustic foam parts in one or both bass reflex channels.
Each component of the crossover is of the best quality and was chosen after extensive listening tests. The most critical capacitor for the tweeter is an oil-impregnated film capacitor.
We have opted for our favourite Mundorf capacitor in terms of sound. We receive these as raw windings and process them in our company according to our ideas and experience to a capacitor with a unique, fine, expressive sound without discolouration. The coil in the bass range consists of individually insulated strands, and we use only our preferred Beyschlag film resistors as resistors. In addition to the classic components used in a crossover, we also use our proprietary InLine Matrix components to avoid magnetic distortions.
All drivers, crossover components, terminals and cables are processed with a special in house developed technology reduce material stress, and so increase the conductivity for complex signals. In addition, we do use our unique quantum physical approach that you also find in our E-Pads. Bobby S and Bobby Bass Extensions are equipped with solid walnut feet for a transparent but organic sound. In addition the Bobby Bass Extensions have receptions for these feet from the Bobby S in their top, and the contact surface is massive mahogany.